Renovations to RK Khan Laboratory

SouthafricaTenders notice for Renovations to RK Khan Laboratory. The reference ID of the tender is 68043213 and it is closing on 30 Jun 2022.

100% Secure Payments

Tender Details

  • Country: South Africa
  • Summary: Renovations to RK Khan Laboratory
  • ZAT Ref No: 68043213
  • Deadline: 30 Jun 2022
  • Competition: ICB
  • Financier: Self Financed
  • Purchaser Ownership: Public
  • Tender Value: Refer Document
  • Notice Type: Tender
  • Document Ref. No.: 1127715
  • Purchaser's Detail :
  • Purchaser : NATIONAL HEALTH LABORATORY SERVICE (NHLS)
    NHLS, 149 Prince Street, Durban
    Email :desmond.govender@nhls.ac.za

  • Description :
  • Quotation are invited for Renovations to RK Khan Laboratory. Important COMPULSORY SITE MEETING: 23 JUNE 2022 @ 10H00 ADDRESS: RK KHAN HOSPITAL, MEET AT NHLS RECEPTION 1 Remove all power skirting and plug points, benches, cupboards and notice boards before demolish brick wall isolate wiring and make good Item 2 Demolish brick wall and make good, 2800mm high m 7.5 3 Remove distribution board with wiring and relocate to passage before breaking wall and removing door and door frame Item 4 Remove all loose and peeling paint from walls, where necessary rhinolite walls to smooth finish, Prepare and paint walls, 2 coats, Plascon Double Velvet, as per specification m2 165 5 Replace broken and missing ceiling boards to match existing, 1200mm x 600mm No 12 6 Remove existing flooring/ ceramic tiles, prepare floor to smooth finish using self-levelling screed, supply and install 2mm Eclipse PUR vinyl sheeting with welded joints as per specification, vinyl must go up the wall 120mm high include cove fillet and capping as per specification m2 170 7 Remove existing light fittings, allow for tubing and wiring to all light fittings, supply and install 1200mm x 600mm x 11mm high slim panel Ecomax 50 watt recessed light fittings No 38 8 Supply and install 30mm x 30mm steel square tubing frame, 650 mm wide and 730 mm high x 3000mm long on lockable 100mm wheels, must be powder coated as per specification No 4 9 Supply and fit 15mm x 700 mm wide, top shall be off approved Phenolic Resin. Top shall be impervious core that is chemical and heat resistant fixed to steel frames, 745 mm high x 3000mm long similar to Fundermax tops No 4 10 Supply and install 30mm x 30mm steel square tubing frame, 650 mm wide and 730 mm high, on lockable 100mm wheels, must be powder coated as per specification m 1.5 11 Supply and fit 15mm x 700 mm wide, top shall be off approved Phenolic Resin. Top shall be impervious core that is chemical and heat resistant fixed to steel frames, 745 mm high similar to Fundermax tops m 1.5 12 Supply and install 30mm x 30mm steel square tubing frame, 600 mm wide and 730 mm high, on adjustable inserts, must be powder coated as per specification m 17 13 Supply and fit 15mm x 700 mm wide, top shall be off approved Phenolic Resin. Top shall be impervious core that is chemical and heat resistant fixed to steel frames, 745 mm high similar to Fundermax tops m 17 14 Supply and install 30mm x 30mm steel square tubing frame, 700 mm wide and 730 mm high, on adjustable inserts, must be powder coated as per specification m 1.5 15 Supply and fit 15mm x 700 mm wide, top shall be off approved Phenolic Resin. Top shall be impervious core that is chemical and heat resistant fixed to steel frames, 745 mm high similar to Fundermax tops m 1.5 16 Supply and fit Black staining integral sink, 500mm x 500mm x 430mm deep with waste grate and Polypropylene bottle trap, connect to water supply and drainage No 1 17 Supply and fit movable swan neck serrated nozzle tap to sink, connect to water supply including shut off valve No 1 18 Supply and fit steel powder coated wall cupboards with doors, 750mm high x 900 mm wide x 330mm deep with shelve as per specification No 7 19 Supply and deliver steel powder coated under bench cupboards 840 mm high x 900mm with drawers on top and doors and shelve at bottom on lockable castor wheels as per specification No 8 20 Remove existing basins, supply and fit porcelain hand wash basin with hospital elbow taps, connect to hot and cold supply and drainage, fit shut off valves to each outlet, fit splash back tiles above basin No 1 21 Supply and fit aluminium power poles fastened to roof rafter and on concrete floor, to accommodate data and electrical wiring No 2 22 Supply and fit 3 x 15 amp standard plug points to each power pole wire from distribution board to prevent overloading including 25 amp circuit breakers No 3 23 Supply and fit, steel, 2 Compartment power skirting, allow for bends and end caps, power skirting from wire ways for power and data reticulation to link to ceiling and distribution board m 56 24 Supply and fit 15 amp standard power skirting plug points, wire only 5 plug per circuit from distribution board to prevent overloading No 46 25 Supply and fit 3 pin 32 amp IP44 male and female socket wired from distribution board with 4mm wire 3 core No 3 26 Remove existing single door, supply and fit aluminium frame with 6 mm safety laminated single glass door, fit 4 industrial door handles with separate lockset, supply and fit 4 heavy duty hinges to door, bottom half of door must be solid aluminium and top half must be clear glass No 2 27 Supply and fit aluminium frame with 6mm safety laminated double glass door, fit 4 industrial door handles with separate lockset, supply and fit 4 heavy duty hinges to each door, bottom half of door must be solid aluminium and top half must be clear glass No 1 28 Remove existing reception counter and partition including door and make good Item 29 Supply and fit aluminium partition 1200mm high with 600mm x 15mm approved Phenolic Resin top. Top shall be impervious core that is chemical and heat resistant counter top similar to Fundermax tops m 1.8 30 Supply and fit aluminium frame with 6mm safety laminated glass above aluminium partition, leave 300mm space for specimens to pass through, height 2600mm m 1.8 31 Supply and fit aluminium frame with 6mm safety laminated glass door, fit industrial door handles with separate lockset, supply and fit 4 heavy duty hinges to door, bottom half of door must be solid aluminium and top half must be glass No 1 32 Windows in to be painted black to match existing, 1700mm x 1400mm No 5.
  • Documents :
  •  Tender Notice

If you are registered member, kindly login to view full details of this tender notice:

CLICK HERE TO LOGIN
SouthafricaTenders Features

SouthafricaTenders Features

Fresh and verified Tenders from Southafrica. Find, search and filter Tenders/Call for bids/RFIs/RFPs/RFQs/Auctions published by the government, public sector undertakings (PSUs) and private entities.

  • 1,000+ Tenders
  • Verified Tenders Only
  • Accurate Tender Information
  • New Tenders Every Day
  • Consultants for RFI/RFP/RFQ
  • Search, sort, and filter Tenders
  • Customer Support
  • Publish your Tenders
  • Consulting Services
  • Export data to Excel or CRM

Get A Call From Tender Experts

Fill out the form below and you will receive a call from us within 24 hours.

Thank You for Contacting ZimbabweTenders !!
Email Id is already exist !!
Invalid Captcha !

Get FREE SAMPLE TENDERS from Southafrica in your email inbox.

  Chat with us